#Carrier fv4bnf003 manual manual#
You can put it in the dryer on low heat to help take the wrinkles and will come out fluffy.ġ.Please allow 1-3cm error due to manual measurement, please make sure you do not mind before you order the comforter set.Ģ.Actual color may vary from the color on your screen due to monitor color restrictions. ãÂÂWarm TipsãÂÂOwing to be packaged on a small box, it might be some wrinkles when you receive it. ãÂÂ∎asy CareãÂÂMachine wash in cold water, gentle cycle, tumble dry on low or dry naturally, do not bleach. This soft and breathable fabric is good for a comfortable nightâÂÂs sleep. It will not put downward pressure on your body. ãÂÂ∏eaturesãÂÂ∜omforter is fluffy and lightweight. ãÂÂ∍esignãÂÂUnique Design:Game pattern for gamer bedding, the comforter color will be very uniform and natural, without fading Extremely soft material keeps you warm and cozy for all seasons. ãÂÂMaterialã Fabric is made of 100% microfiber.Comforter filling is 100% polyester. Time will tell.ãÂÂSizeãÂÂPackage Includes(Twin Size Comforter Set Only 1 Pillowcase).ġx Comforter: 68 x 86 inches/173 x 218 cmġx Comforter: 79 x 90 inches/200 x 230 cmĢx Pillowcases: 20 x 30 inches/50 x 75 cmġx Comforter: 90 x 90 inches/228 x 228 cm I changed all the jumpers based on my system and the guide. Wen through the manual for these settings and also found the quick reference guide at the end of it. The new guy did wire up Dh to * properly but didn't configure the rest of it. Opened the cover on the system and found both techs from the vendor had left all the easy select settings to default. After he left, I went through the FV4C manual to see if they set it up properly. He set the "Dehumidify with AC" to energize * with the fan activated. He wasn't sure of the settings but felt confident the Nest was setup properly. He removed the J1 jumper, ran a wire from Dh and connected to * on the Nest.
He found the previous tech didn't setup the feature dehumidification feature of the system. HVAC company came back out today sending a new tech. If we do not have the part you need in stock. We stock many different blower motors in our warehouse located in West Newton on the southwest side of Indianapolis. So far it seems to be working as the humidity dropped from 64% to 55% as of now. If you need the blower motor for your Carrier gas furnace, heat pump or air conditioner Shortys HVAC Supplies can provide you the factory authorized blower motor. TL DR, "Dehumidify with AC" set to de-energize * is correct and I saw no difference with the fan setting so I left disabled. House was humid so I called them asking to check the system was setup properly for dehumidification (heck, I paid extra for the comfort feature). I went through this setup today after my recently installed HVAC system wasn't properly setup by my vendor last month. I chose "Not" because AC should turn on the fan itself.Īppreciate if someone with experience could provide some insight. Could someone with experience confirm that?Īnother selection is when dehumidification is called, system should "Activate fan" or "Not". And that means if no dehumidification is needed, the * terminal should be closed (energized).
It seems like I should choose "de-energize the * terminal".
From the air handler manual, when dehumidification is needed, thermostat would open circuit R to DH, to reduce fan speed. Nest ask To dehumidify, energize or de-energize the * terminal. The on Nest setup, choose Dehumidifier for *, and choose "Dehumidify with AC". On the air handler control board, remove the J1 jumper between the R and DH (dehumidifier) terminal.Ĭonnect a wire to the DH terminal, and the other end of the wire to the * (star) terminal on the Nest. I try to set it up with the Nest but I am not sure which setting on the Nest should I choose. I have a Carrier/Bryant FV4C variable speed air handler that has its own Dehumidifier mode.
0 kommentar(er)
